How to Measure and Install Custom Pool Safety Covers

A custom pool safety cover is a useful accessory that will help you protect and maintain your pool. It prevents the accumulation of dirt and other materials within your pool as well as guaranteeing safety for children and pets. 

The Importance of Pool Safety Covers

Pool safety covers are an important necessity to avoid any danger in the pool, especially for kids and animals. They serve as physical barriers whenever the pool is not in use to prevent drowning. They also shield the pool from contaminants and cut the time needed to clean, thereby increasing the life cycle of the pool.

How to Measure and Install Custom Pool Safety Covers

Here is a step-by-step process to follow:

Step 1: Measure Your Pool

The first and most important step for installing a custom pool safety cover is measuring:

• Take the dimensions of the length and the width at the end of the pool and where it is widest. Add any protrusions or recessions that may cause the fit to be tight for complex shapes.
• Take some measurements across the pool to ensure that it has not sagged at some points.
• Determine the pool edge to the deck to ensure a good fit of the cover on the pool.

Make sure that you record these measurements when ordering your customized cover.

Step 2: Choosing the Right Pool Safety Cover

After getting the measurements, you should decide which material you want to use to create the custom safety cover. Most pool safety covers are either mesh or solid:

• Mesh covers: These let water pass through, but a little debris may also find its way through.
• Solid covers: These offer a total shield against any debris but will require a drain system in order not to accumulate water.

Choose a cover that meets your requirements as far as drainage and protection against debris are concerned. Mesh covers are generally more user-friendly and have better water-shedding properties than solid covers, but the pool looks cleaner with a solid cover.

When placing an order for your custom pool safety cover, make sure that you give the correct measurements so that the cover will fit your pool well. Most suppliers provide custom-built services to ensure a proper fit.

Step 3: Prepare the Area for Installation

In preparation for the installation of a custom pool safety cover, it’s a good idea to prepare the surroundings of the pool. Remove any debris from the pool deck and ensure that the pool is cleared of any large objects and dirt deposits. This will ease the installation process as there will be no interference that could be trapped beneath the cover once it has been fitted.

Step 4: Install the Pool Cover Anchors

At this point, you can proceed with fitting the custom safety cover for swimming pools. Start by placing the cover on the pool and adjusting it to the right position. Now that the cover is in place, it’s necessary to position the anchors after the edges of the cover are in alignment with the edge of the pool.

These anchors will lock the cover around the pool deck and will provide a sturdy hold for the cover over the pool. In general, the anchors are located along the edge of the pool deck, marking the circumference of the pool. Make small holes in these spots and carefully place the anchors. For obvious reasons, check that the anchors are not too loose.

Step 5: Attach the Cover’s Straps or Cables

Once the anchors are installed, you can move on to attaching the cover’s straps or cables. Begin by connecting each strap or cable to its corresponding anchor. Make sure to tighten the straps so that the cover fits snugly over the pool. If your cover uses springs, stretch them tightly to ensure they hold the cover securely in place.

Check that the cover is evenly spread across the pool, with no sagging or gaps. The aim is for the cover to be taut and properly secured around the pool. Adjust the straps or springs as needed to achieve a tight, smooth fit.

Step 6: Check the Fit and Tighten

After all the straps or cables are attached, take a moment to check the cover's fit. It should be snug and taut, with no slack that could lead to sagging. If the cover isn’t tight enough, tighten the straps or springs until it fits securely.

A well-installed pool cover should remain in place, protecting your pool from debris, dirt, and any accidental falls. Make sure the cover is securely fastened before considering the installation complete.

Step 7: Maintain the Pool Cover

After installation, it's crucial to regularly check the cover for any signs of wear and tear. Inspect the straps, anchors, and springs for any damage, and replace any broken or loose parts. Consistent cleaning and maintenance will help prolong the life of your custom pool safety cover and keep it in good shape for years to come.

Protect Your Pool Today

Installing a custom pool safety cover is a straightforward and effective way to maintain the safety and cleanliness of your pool. 

If you're ready to safeguard your pool with a custom safety cover, contact People for Pools today. Our team is here to assist you throughout the process, ensuring your pool is safe, secure, and ready for enjoyment. Begin your pool protection journey now!